- Terminate a smooth railing surface into a wall.
- This fitting should not be used as a base flange.
- See Usage Pictures in the Gallery
- There is a fee per fitting. Click here for powder-coating pricing. The cost goes down the more fittings you order.
- powder-coating can be done in any RAL Color (see the chart)
- powder-coating adds about two weeks of lead time.
The Wall Flange Fitting is available in two configurations:
The 514 fitting is required when using this component. The 514s connect the pipe to the fitting, form a smooth railing surface.
The Kee Access ADA Railing System is a cost effective handrail installation suitable for stairs, ramps or walkways that conform to the railing requirements of the American with Disabilities Act (ADA). An ADA railing is a framework of horizontal rails supported by vertical uprights (posts), assembled from fittings and pipe. This type of railing provides a contiguous gripping surface throughout its entire length.
The modular Kee Access Railing fittings securely join standard sizes of schedule 40 galvanized steel pipe and is flexible enough to accommodate most variations between design drawings and site requirements. The system does not require any drilling, welding or threading, and is easily assembled without specialized workers or equipment. All fittings are galvanized for low long-term maintenance and can be powder coated to your choice of RAL Colors.
Frequently Asked Questions
Does the fitting come with set screws?
Are these fitting available in colors?
Yes. Kee Klamp, Kee Lite, Kee Access fittings and pipe can be powdercoated to give them a durable baked on paint finish. powder-coating is extremely durable and will give your railing or structure a really sharp look.
Please contact us if you have any questions about powder-coating.
What kind of pipe can be used with Kee Klamp and Kee Lite fittings?
Kee Klamp and Kee Lite components are designed to be used with Schedule 40 Pipe (or Schedule 80), but can also be used with other types of pipe or tube.
When acquiring your own pipe and tube it is important to know the actual OUTER DIAMETER of your pipe/tube . Do not assume that just because it says 1 Inch Pipe/Tube for instance, that the outer diameter is actually 1 inch. This mistake frequently results in returns.
If you are purchasing fittings and pipe from our website, match the pipe size with the fitting size such as Size 7 pipe with Size 7 fittings, Size 8 pipe with Size 8 fittings, etc. You may also refer to our SIZING CHART for further help.
How can I be sure I'm ordering the right size fittings?
If you already have pipe, please measure the outer diameter of your pipe and compare it to the chart on this page. For simplicity we have a printable pipe chart that you can use to measure your pipe. Be sure to follow the instructions on the sheet to guarantee an accurate measurement.
If you are purchasing your pipe from us, then be sure to match the size after the dash '-' on the fittings to the size of the pipe. For instance, a 10-7 is a size 7 fitting. Select size 7 pipe to go with that fitting.
|Model||Measurements (in.)||Weight (lbs.)|
|561 / 514-7|
|Model||Measurements (mm)||Weight (kgs)|
|561 / 514-7|
Pipe Size Chart
The chart below will help you understand how to match the size of fittings and pipe.
|Size / Fits Pipe:||7 / Outside Diameter 1.660"|
|Fits Pipe OD||1.660"|
|Fits Pipe (Nominal Bore)||1-1/4"|
|Loads||A Kee Klamp component (size 5 to 9) can support an axial load of 2000 lbs. per set screw with the set screw tightened to a torque of 29 lbs/ft. (rating includes a safety factor of 2:1)|
|Set Screw||Case hardened steel, Kee Koat corrosion resistant coating|
|Standards||ASTM A47-77-32510, BS EN ISO 1461|