Shopping Cart
To Receive a Quote Call Toll-Free: 1.888.527.2278 or email sales@simplifiedbuidling.com

KeeGuard® Roof Top Railing System

The Highest Quality Free Standing, Roof Edge Fall
Protection System on the market

Today's strict legal requirements require employers to ensure a proper safety management program for employees working at heights (reference). The KeeGuard Roof Edge Fall Protection System can ensure the proper health, safety, and well being of your employees.

KeeGuard is Non-penetrating

KeeGuard is a free standing system that does not penetrate the roof membrane. KeeGuard has a patented counter balance systems that allows you to protect workers on your roof without the need to screw or drill into the roof membrane. Special pads on the bottom of the weights and kickboard fitting provide an extra layer of protection.

Flexible & Cost Effective

KeeGuard is supplied in pre-fabricated modular kit form with an integral kickboard fixing and a minimum number of assemblies allowing for ease of installation. The system's modular components allow installation of a 600 foot run by 2 people in 8 hours, saving you time and money where it counts most - on site. The system’s modular components also allow for installation on even split-level and low slope roofs.

Essential Fall Protection

KeeGuard has been fully tested, and when installed properly exceeds OSHA standards. The KeeGuard System can be used for roof edge fall prevention, walkway demarcation, stairwells, open elevator shaft fall protection, skylight fall protection, and fulfillment of other prescribed safety requirements. Get a quick estimate by filling our Quote form.

Watch the video below for a complete overview of the
KeeGuard Roof Top Fall Protection System.

Safety - KeeGuard not only meets but exceeds current safety requirements for maximum roof edge protection.

  • KeeGuard Assemblies use fittings that are TÜV tested and approved
  • Integral toeboard fixings for full health and safety compliance
  • Assemblies are fitted with anti-slip rubber pads for safety and to protect the roof membrane
  • Works on a tested and proven counterbalance system

Durability - KeeGuard components are galvanized providing long lasting roof fall protection you can depend on.

  • All pipe is galvanized to ASTM A53
  • All fittings are galvanized to meet the requirements of EN ISO 1461:199
  • Featuring case hardened steel set screws with Kee Koat™ protection
  • Uses reliable Kee Klamp® fittings which provide strong, rigid, virtually maintenance free connections

Versatility - KeeGuard employs a pre-fabricated modular design that allows you to reconfigure your system on site with ease if needed.

  • Sections can be added to, or taken down and re-erected on site
  • A variety of uses including skylight protection, walkway demarcation, stairwell protection and more…
  • Compatible with almost all variations of flat roofs (up to 3 degrees), be they circular, square, rectangular or multilevel
  • Available from our warehouse or through authorized installers

Simplicity - KeeGuard has a unique modular design that takes the complexity and cost out of roof edge fall protection – for good.

  • Unique open style fitting allows quick installation of horizontal rails
  • Minimum components for ease of fitting and installation
  • Uprights allow angle adjustment of up to 11 degrees
  • No drilling, special anchoring or penetration of the roof membrane
  • No welding, bending or threading required on site, and no specialty tools are needed

Standards - KeeGuard has been independently tested and meets or exceeds the following North America and International Requirements:

  • OSHA Standard 29 CFR 1910.23
  • OSHA Standard 29 CFR 1926.501, 29 CFR 1926.502
  • Canadian National Building Code 4.1.10.1(1)(e), 4.1.10.1(2), 4.1.10.1(4)
  • Ontario Building Code Section 4.1.10.1(1)(b), 4.1.10.1(2), 4.1.10.1(4)
  • HSG-33 Health & Safety in Roof Work
  • HSE Specialist Report No 15: 1988
  • HSE Sheet 21 “Working on Flat Roofs Protection Against Falls”
  • BS 6399: Part 2 1995 Wind Code
  • EU Directives & CDM Regulations
  • BGV A1: 2000, BGG 928 & BGR 184
  • Health, Safety & Welfare Regulation 13 “Falls or Falling Objects” 1992
  • NFE 85-003
  • EN ISO 14122: PT3

Environmental Friendliness - the innovative counterbalances are engineered to be environmentally friendly. Each counterbalance is made from 100% recycled PVC to replace the previous counterbalance, which was composed of galvanized steel.

  • Carrying handles molded into design
  • Available in grey, orange, and custom color
  • Reflective labels on each weight
  • Surface promotes traction and grip
  • Made from 100% recycled PVC

 

Site Terms | Terms and Conditions of Sale | Privacy Policy
Blog | About Us | Contact Us
© 2008 Simplified Building Concepts, All Rights Reserved
Site Design By: http://web.simplifiedbuilding.com
Rapid SSL Cert
BBB Reliability Program